nomadwireless.blogg.se - Keil uvision 5

#KEIL UVISION 5 HOW TO#
#KEIL UVISION 5 PRO#
#KEIL UVISION 5 SOFTWARE#
#KEIL UVISION 5 CODE#

I have reverted to my known working code from several months ago(prior to any problems) and problem persists.

#KEIL UVISION 5 PRO#

I tried tried two adapters (J_Link Pro and Flasher) and both adapters exhibit the same problem.

#KEIL UVISION 5 HOW TO#

It seems that uVision has "forgotten" how to connect to my device, but it can use a connection established by J-Flash.ĭuring my investigations, I have found that the JTAG device chain (see attached screenshots) is populated when when J-Flash has connected, but is empty when J-Flash has not connected.

start J-Flash open a flash project and connect (Target->Connect) to the device.

My process to start debugging in uVision is: Now I have to run J-Link Flash to manually establish a connection (via J-Link Plus) to my device.

Start debugging (Ctrl-F5) which would flash my new binary and stop at main().

selamat mencoba, dan jangan lupa terus berkunjung di blog in the last month or so, uVision has stopped connecting to debug my device.īefore my problems started, my process start debugging in uVision was: Kemudian BUILD dan UPLOAD/LOAD programnya, silahkan amati hasilnya, jika LED sudah berkedip berarti anda sudah berhasil. * (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ Tex: printf("Wrong parameters value: file %s on line %drn", file, line) */ * User can add his own implementation to report the file name and line number, Void assert_failed(uint8_t* file, uint32_t line) * line: assert_param error line source number * where the assert_param error has occurred. * Reports the name of the source file and the source line number * User can add his own implementation to report the HAL error return state */ * USER CODE BEGIN Error_Handler_Debug */ Void _Error_Handler(char *file, int line) * This function is executed in case of error occurrence. GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0) * SysTick_IRQn interrupt configuration */ HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK) HAL_SYSTICK_Config(HAL_RCC_GetHCLKFreq()/1000)

If (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0) != HAL_OK) RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1 RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1 RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1 RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2 RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK

If (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) RCC_OscInitStruct.HSICalibrationValue = 16 RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI **Initializes the CPU, AHB and APB busses clocks _HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE3) **Configure the main internal regulator output voltage HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_RESET) HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_SET) * Initialize all configured peripherals */ * Reset of all peripherals, Initializes the Flash interface and the Systick. * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * SERVICES LOSS OF USE, DATA, OR PROFITS OR BUSINESS INTERRUPTION) HOWEVER * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE

#KEIL UVISION 5 SOFTWARE#

* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * without specific prior written permission. * may be used to endorse or promote products derived from this software Neither the name of STMicroelectronics nor the names of its contributors * and/or other materials provided with the distribution. * this list of conditions and the following disclaimer in the documentation Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer. Redistributions of source code must retain the above copyright notice, * are permitted provided that the following conditions are met: * Redistribution and use in source and binary forms, with or without modification, * are owned by their respective copyright owners. * inserted by the user or by software development tools

* that are not between comment pairs USER CODE BEGIN and ** This notice applies to any and all portions of this file Selanjtnya kita tinggal membuat program blink nya, Replace saja code dalam main.c nya dengan code berikut : /**